Showing results 1 to 9 of 9

Thread: Virtual SCSI Not Found (W2k)

  1. #1

    Default Virtual SCSI Not Found (W2k)

    Here are the specs:
    AMD T-Bird 1Ghz
    Corsair XMS3300 256MB
    DFI AK-76SN
    Maxtor Diamond Max Plus 60 40GB HD

    I don't have either EasyCD Creator or Nero installed so there is no nerocd95.vxd. However I stil get Virtual SCSI Not Found error. I'm running Win2k Data Center. If you can help me solve this problem then please email me or reply. Thanks a lot.

  2. #2

    Default

    I just found out that the drive/scsi is found when I'm at the computer itself. However, when I connect to this computer using Remote Desktop control or terminal service from elsewhere, the drive is not detected.

  3. #3
    New User
    Join Date
    03.03.2003
    Posts
    1

    Default Same problem under XP Pro

    I get the same message under Win Xp Pro. I started receiving it immedialtely after the installation of D-Tools, not after some upgrade of XP. Uninstalling and re-installing does not solve the problem, although uninstallation goes without problem (I am not asked about this .msi file).

  4. #4

    Default

    @DepecheNYC: Is it possible there are some security issues with remote desktop. I mean, maybe a remote user would have little need to access a cdrom and ms disables it? I will test this out on winxp though.

    @Ivo: Run devmgmt.msc, goto scsi and system devices section. Report the status (error code+message) of the st3??? and PNP bios extension.

  5. #5
    New User
    Join Date
    12.03.2003
    Posts
    3

    Default

    I've got a similar problem. I recently installed 'clean' XP Pro and soon after Daemon tools. No prob with installing but after reboot I got error message "Virtual SCSI driver not found". I uninstalled and reinstalled DTools and everything worked fine until next reboot.

    Device Manager gives following error for virtual SCSI controller. Plug and Play BIOS extension is working properly.

    ST3MP28 SCSI Controller
    This device cannot start. (Code 10)

    Click Troubleshoot to start the troubleshooter for this device.

  6. #6
    Administrator



    Join Date
    06.11.2002
    Posts
    2,044

    Default

    @ze303:What is displayed in device manager before you reboot (after installation)?

  7. #7
    New User
    Join Date
    12.03.2003
    Posts
    3

    Default

    @VeNoM386: It shows all devices mentioned before working properly.

    I found that after reboot, simply by disabling and re-enabling the ST3XXX controller in device manager, DTools will function again (atleast until the next reboot :) I hope this work-around helps until a more permanent solution comes up...

  8. #8
    Administrator



    Join Date
    06.11.2002
    Posts
    2,044

    Default

    Do you see any errors in the system event log originating from st3mp28.sys ?

  9. #9
    New User
    Join Date
    12.03.2003
    Posts
    3

    Default

    Yes.

    Event Type: Error
    Event Source: st3mp28
    Event Category: None
    Event ID: 4
    Date: 12.3.2003
    Time: 17:55:35
    User: N/A

    Computer:
    Description:
    Driver detected an internal error in its data structures for .

    For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
    Data:
    0000: 00 00 00 00 01 00 58 00 ......X.
    0008: 00 00 00 00 04 00 04 c0 .......А
    0010: 7f 4d 4f 80 c0 00 00 c0 MO€А..А
    0018: 00 00 00 00 00 00 00 00 ........
    0020: 00 00 00 00 00 00 00 00 ........

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •