Announcement

Collapse
No announcement yet.

device setup error: code 25032

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Sorry, use venom386@daemon-tools.cc!
    Everybody be cool! You, be cool!
    They'll keep fighting! And they'll win!

    Comment


    • #17
      Yes, i corrected the address. Sorry.

      Comment


      • #18
        Everytime i write to that adress, my mail program tells me i have a delivery failure because the adress doesn'T exist? Are u guys kidding me or what?

        Comment


        • #19
          No, we are not kidding, venom386@daemon-tools.cc is the correct adress.

          Please try again, it's possible that it was a temp-problem (yesterday great networkareas in germany got trouble because of traffic-load)

          Comment


          • #20
            same problem

            Operating System: Windows Me
            Burning Software: none
            Anti-virus Software: mcafee v7.02 updated
            DAEMON Tools Version: 3.41

            I had the same problem.
            I installed dtools 3.41 over 3.16(without uninstalling it)
            when installing, near the end
            "Device setup error: code 25032(0x31C8)
            0(0x0)"
            I got too an unknown device, tried deleting it(the device) and running the repair from the setup, but exactly same problem comes
            Im gona try an older version(had no probs with 3.16)
            Added info: installed 3.32 and everything is ok

            Comment


            • #21
              Before you press ok, please watch in the device manager - what unknown device you have and its status?

              Comment


              • #22
                Virtual SCSI Drive not detected; error codes 25001 25032

                Operating System: Windows 98 SE
                Burning Software: Easy CD creator (uninstalled thoroughly)
                feurio, CloneCD
                Anti-virus Software: AntiVir
                DAEMON Tools Version: 3.41

                Installation terminates with error codes 25001 and 25032. After installing again virutal SCSI driver cannot be found.
                In the device manager there are two unknown devices in folder computer-->system device-->unknown device. Removing them and reinstalling dt does not help.
                Used feurio to detect driver conflicts and installed new Aspi driver: does not help either.
                Same problem with Alcohol120.

                Comment


                • #23
                  ASPI driver is irrelevant for Daemon/Alcohol absolutely, they don't need it.
                  Delete all unknown devices and reboot. Then try to run setup - when you get 25032 - DON'T do anything! Immediately go to device manager and check what is there and with what status.

                  Comment


                  • #24
                    Directly after error code 25032 (0x61C8)
                    (0x0) there is only one unknown device (with exclamation mark) and the status is: no drivers installed (Code 28).

                    Comment


                    • #25
                      You have smth either with antivirus (try to disable it) or Windows file protection. Do you see pnpshark.inf in the WINDOWS\INF folder?

                      Comment


                      • #26
                        Sorry, AntiVir doesn't seem to be the cause/curse and no pnpshark in windows/inf.

                        Comment


                        • #27
                          3.41 setup copies this file to Windows\inf folder. Check it good BEFORE you press ok after error (after you press ok setup will rollback and delete it).
                          If you still not see it - then problem is with Windows file protection.
                          Addition: as you use 98 then file protection has nothing to do here (it is in ME only)
                          in this case i have no idea what's going on.

                          Comment


                          • #28
                            Before pressing Ok, pnpshark is there, indeed

                            Comment


                            • #29
                              Do you see the dialog of Windows rebuilding driver list during installation?

                              Comment


                              • #30
                                Yes

                                Comment

                                Working...
                                X