PDA

View Full Version : After reboot -> invalid device



mphiz
04.10.2003, 19:48
Operating System: WinXP Home SP1
Burning Software: Nero 6
Anti-virus Software: no
DAEMON Tools Version: 3.41

hi

this sucks, when i install dt and restart it works but when i restart again it says "Invalid Device". so i need to delete-install dt and reboot every time to use it :evil: .

Development
04.10.2003, 20:01
Instead of uninstalling you better go to device manager and check status of devices.

mphiz
04.10.2003, 21:55
it says: The device cannot be started. (code 10) :?

Development
04.10.2003, 22:23
Now check system event log - any error messages there from st3shark? Post here all binary dump bytes please.

mphiz
04.10.2003, 23:46
ewww what i have to do? :(

Development
05.10.2003, 00:30
ControlPanel->AdministrativeTools->ComputerManagement->SystemTools->EventViewer->System

mphiz
05.10.2003, 02:00
0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 00 00 00 00 c0 00 00 c0 ....А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

is that right ?

Development
05.10.2003, 02:35
Only this one entry, no other errors? What is event ID and what is written above it?

nepo65
05.10.2003, 11:50
Operating System: Windows XP Home SP1 with latest updates
Burning Software: Nero 5.5.10.50
Anti-virus Software: Norton Anti-Virus 8.07.17c
DAEMON Tools Version: 3.3.3

Since I have the same problem I think I join this discussion.
With my Daemon Tools I suddenly had this "SCSI device not detected" message. It just appeared one day and never went away from that on. I fo not remember if it happend after an update of some software or so.

The system event log reports an error:
source: st3wolf
event ID: 4

Description (translated from German): The driver detected an internal error in its data structures
0000: 00000000 00580001 00000000 c0040004
0010: 00000000 c00000c0 00000000 00000000
0020: 00000000 00000000

I have not tested this with the latest version of Dameon Tools.

mphiz
05.10.2003, 12:00
above bytes, same as nepo

Fiskemanden
05.10.2003, 13:52
Operating System: XP
Burning Software: Nero 6
Anti-virus Software: Norton
DAEMON Tools Version: 3.41

Event Type: Error
Event Source: st3shark
Event Category: None
Event ID: 4
Date: 05-10-2003
Time: 12:59:07
User: N/A
Computer: FISKEMANDEN
Description:
Driver detected an internal error in its data structures for .

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 80 c6 b0 f8 c0 00 00 c0 €Ж°шА..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

This is the error, that I get, after installing DT 3.41

krisse
05.10.2003, 16:35
Operating System: win xp
Burning Software: nero5
Anti-virus Software: norton 2003
DAEMON Tools Version: 3.41

Event Type: Error
Event Source: st3shark
Event Category: None
Event ID: 4
Date: 2003-10-05
Time: 15:55:04
User: N/A
Computer: KRISSE

Description:
Driver detected an internal error in its data structures for .

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

Data: (X) Bytes ( ) Words
0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 52 00 4f 00 c0 00 00 c0 R.O.А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

Data: ( ) Bytes (x) Words
0000: 00000000 005a0001 00000000 c0040004
0010: 004f0052 c00000c0 00000000 00000000
0020: 00000000 00000000

vince_mtp
05.10.2003, 21:43
Operating System: Windows XP professional
Burning Software: Nero 5.5.9.9, CD Mate 2.2.8.1
Anti-virus Software: Norton SystemWorks 2002
DAEMON Tools Version: DAEMON Tools 3.41.0

Hi everbody,

I installed DAEMON Tools today and the same thing appends to me : hte first time I works perfectly, but after I rebooted my computer, when I want to launch DAEMON Tools, I have 2 successive error message dialogs which both say "Invalid Device".... :( :?:

It's not the first time I've this problem, I've alraedy installed DT on my computer a couple of months ago, and i had the same problem, I needed to de-install it and re-install i after each system reboot.
But today is the first time I install it on my computer until the last time I reinstalled Win XP...
I don't have de-installed DT yet.

Here is my System Log from SystemTools->EventViewer : (i'm french, so is my WinXP version and so are the logs) :

I've got 3 errors after system reboot (I cleared system log before reboot) :


error # 1 :


Le pilote de démarrage système ou d'amorзage suivant n'a pas pu se charger :
[b]st3shark[/b]

Pour plus d'informations, consultez le centre Aide et support а l'adresse http://go.microsoft.com/fwlink/events.asp.


error # 2 :


Le service General Purpose USB Driver ([b]adildr.sys[/b]) n'a pas pu démarrer en raison de l'erreur :
Le service ne peut pas кtre dйmarré parce qu'il est désactivé ou qu'aucun périphérique activé ne lui est associé.

Pour plus d'informations, consultez le centre Aide et support а l'adresse http://go.microsoft.com/fwlink/events.asp.

error # 3 :


Le pilote a détecté une erreur interne dans ses structures de données pour .

Pour plus d'informations, consultez le centre Aide et support а l'adresse http://go.microsoft.com/fwlink/events.asp.

DATA : octets

0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 00 00 00 00 c0 00 00 c0 ....А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

I don't know what to do...
please help !!! :( :!: :cry: :oops:

thx ;) :oops:

Development
05.10.2003, 22:17
It would be nice if you could translate it for me;)
What it means:
Le service ne peut pas кtre dйmarré parce qu'il est désactivé ou qu'aucun périphérique activé ne lui est associé.

@Other guys: you have only error from st3shark or other devices too?

mphiz
05.10.2003, 22:41
The following boot or system start drivers load failed:
st3shark
tvtool (another program)

Data:
nothing
-----------------------------------------
another fail:
(translated with altavista^^)

AMLI: Acpi bios tries to read from an invalid I/O port address (0x71) itself in "0x70 - 0x71", a protected address range, finds. This can lead to the system instability. Contact the system manufacturer, in order to receive technical support.

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

Data:
0000: 00 00 00 00 04 00 52 00 ......R.
0008: 00 00 00 00 04 00 05 c0 .......А
0010: 00 00 00 00 00 00 00 00 ........
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

Development
05.10.2003, 22:45
When you remove Daemon - you get no more ACPI error?
@vince_mtp: i heard nothing about adildr.sys which is called 'General Purpose Driver' - try to rename/remove it for test. Where it comes from?

vince_mtp
05.10.2003, 22:52
sorry :oops: :oops: :oops:

it must be something like :

error # 1 :

the system boot driver or the launch driver couldnt' be loaded : st3shark

error # 2 :

the service General Purpose USB Driver (adildr.sys) couldn't be started because of the error :
the service cannot be started because it is not activate or no active peripheral is assigned to it.

error # 3 :

the driver has detected an internal error in his data structure for : (??? empty...)

And the option "Octets" is selected with the value :


0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 00 00 00 00 c0 00 00 c0 ....А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

is it clearer now ???

ps : I don't have any SCSI card in my computer...

pps : I don't have any "General Purpose USB Driver" in the services list from control panel -> admin tools -> services.... :? , neither any service with "usb" in its name (in french...) (I exported the list and searched in it)


thx for trying to help me :) :oops:
Vince

Development
05.10.2003, 22:57
So rename for test. Do you get 2 consecutive errors in log from st3shark after 1 boot?
Please post bytes for all them please, it is very important.
I don't see bytes from error 1.

vince_mtp
05.10.2003, 23:01
ok i'll rename it and reboot for test.

i have to leave now but i'll be back to test in 3/4h ~1h

see U

Vince

vince_mtp
06.10.2003, 00:38
okay,

I cleared the logs before rebooting my computer.
Before, I found that the 2nd error comes from my ADSL modem driver... so don't take care about it.

Here are the logs after rebooting : (and before launching DT)

ERROR 1

Source : Service Control Manager
Event ID : 7026
Desc : the system boot driver or the launch driver couldnt' be loaded : st3shark
DATA : disabled, "octets" is selected, but there is no text.

ERROR 2
Source : Service Control Manager
Event ID : 7000
Desc : General Purpose USB Driver (adildr.sys) ...... useless here I think
DATA : disabled, "octets" is selected, but there is no text.

ERROR 3
Source : st3shark
Event ID : 4
Desc : the driver has detected an internal error in his data structure for .

Pour plus d'informations, consultez le centre Aide et support а l'adresse http://go.microsoft.com/fwlink/events.asp.

DATA : enabled, "octets" is selected, text is :


0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 00 00 00 00 c0 00 00 c0 ....А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

This 3 errors are EXACTLY the same, whether I move the adildr.sys OR NOT.

However, I found something :
In the peropheral gestionnary, DT has created :

_ My computer
|_ SCSI & RAID controller
|_ ST3SHARK SCSI Controller => this one has a conflict

His properties are :

- General :
This peripheral cannot start (code 10).
and it is activated (in the combo box at the bottom of the dialog)
- Driver details :
C:\WINDOWS\System32\DRIVERS\st3shark.sys
- Ressources :
no ressource
list of perpherals in conflict : none.

When I launch DT I've got 2 error dialog boxes which both says "Invalid device" but there is no new line in the system event diary.

...

hope this helps

Vince

Development
06.10.2003, 01:05
Your installation is broken - uninstall Daemon and make sure no SCSI virtual controllers are present, if yes - delete them. Then reboot and run setup. After setup is completes - go to device manager, there must be exactly 1 controller only 'ST3SHARK SCSI Controller' - nothing else!

You can now also try to delete that SCSI/RAID controller and reboot.
Check what happens. If it reappears, then delete ST3SHARK SCSI Controller and reboot.

vince_mtp
06.10.2003, 01:17
:?
think HTML has mistaken you : my schema of the device manager has been modified because I used spaces.

I already have only 1 controller

I will try to make a new schema (I will use dots instead of spaces :oops: ) :

DEVICE MANAGER :

[-].[My computer name]
.......|_ [-]. SCSI & RAID Controllers
.......|.........|_. :!: ST3SHARK SCSI Controller

that's my device manager view... :? :? :?

vince_mtp
06.10.2003, 01:22
I found something !!! :idea:

I right clicked on ST3SHARK SCSI Controller ans hit "properties".
then i clicked on "driver" and on "update driver".
windows XP updated it and when I clicked on "finish" the :!: disapeared and DT works now !!!

I'll reboot to test whether it's ok or I'll have to do it every time (that's better from uninstalling and reinstalling it every time !!!) :lol:

I'll be back in 5 minutes... 8)

vince_mtp
06.10.2003, 01:28
.....

it don't works again...
and updating the driver don't runs so... DT cannot start, I've got the 2 error dialogs... :evil:

what's happening :?: :? :shock:

Development
06.10.2003, 01:40
Disable that adildr.sys completely. If you still have that entry then delete
HKLM\System\CurrentControlSet\Services\Atildr key and reboot.
First check what software it is from, maybe look at file resources may give the clue.

vince_mtp
06.10.2003, 01:45
this ressource is one of my modem driver's, it is in a directory xith my modem's name, I won't delete it !!! :?

I've just rebooted again. I've noticed just before that that the SCSI controller name changed from ST3SHARK to "Host Controller SCSI/RAID"
I think that driver Windows found was a generic drvier, and when I restared, it just didn't workd again... because of the change windows made.
in fact I don't understand that it worked 10 min ago... :?

Well, I launch DT install and before rebooting during the install (I don't remember whether or not DT asked me for rebooting the first time I installed it, but it just asked it now...) I checked my device manager and I have only 1 SCSI device which is ST3SHARK again.

So at this time DT works, but only until the next reboot it think... :( :( :(

Development
06.10.2003, 01:52
I understand. But anyway your system has trouble if even your modem driver cannot start. Remove Daemon completely from system. Is adildr ok? If not - you should care about it first. Daemon must be installed on fully operating system only.

vince_mtp
06.10.2003, 01:56
ok, I understand, but I already had this conflict before I install DT (at each of my system reinstallation)
so.... I want to use DT even with this problem if I can !!! :wink: :lol: (moreover, my modem don't seems to be disturbed.... :? )

well, the others have the same problem, maybe you'll be able to help them and me by the same way ;) :)
I'll keep an eye on this topic, but if you found the solution to this problem, please email me ;)

ps : I never used Easy CD Creator on my computer.

well...time to sleep !!! :lol:
thx
Vince

vince_mtp
06.10.2003, 02:02
ps : I already had the problem i the past with DT 3.26 & DT 3.29...

may be this can help... :?

bye
Vince

Development
06.10.2003, 02:13
I will try to investigate what happens by making special version of st3shark.sys for you which dumps more messages to event log.
Our mail server is currently down, after it is ok - i will let you know.

vince_mtp
06.10.2003, 02:18
OK, I will be pleased to help you ! :):):)

bye
Vince

Development
06.10.2003, 02:54
Check your email please.

vince_mtp
06.10.2003, 20:08
same thing for U ;)

bye

nepo65
06.10.2003, 20:19
I just wanted to say that the problem went away on my PC with Daemon Tools Version 3.41. However, I do not really know if the problem went away because I installed the new version. I also went to Windows Update and loaded new security patches there.
However, Thanx for the support

Fiskemanden
07.10.2003, 00:20
I totally lost here..

I have uninstalled DT 3.41 and tryed to installed a older version 3.31..

That seems to work, undtil I restartet the computer..
Then the error pop ups again..
I have also tryed to installed Alcohol 120%, but the program gave me a error every time, the computer was restartet...

This is the error, that I got, after restartet with DT 3.31 installed.

0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 80 c6 b0 f8 c0 00 00 c0 €Ж°шА..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

The new problem that I gets, is that I get a error under Device Manager..
" PnP Bios Extension " -- Windows cannot load the device driver for this hardware. The driver may be corrupted or missing.

What the devil is that? I have never had this problem before.. Is it relatet with Deamon Tool??

I hope that I soon will be able to again use DT without any problems :-)

vince_mtp
07.10.2003, 00:55
VeNoM386 : I have send you back my email

Vince

CptMiller
15.10.2003, 12:07
Operating System: Windows XP Home Edition
Burning Software: Nero 5
Anti-virus Software: no
DAEMON Tools Version: 3.41

I have the same problem!
what can i do against it?
Can you send me this driver please (which reports errors a little bit better)?
I have the same problem with Alcohol 120 %!
please help me to fix that!

Development
15.10.2003, 13:27
Those who have such problem with 3.41 can mail me for temporary fix

CptMiller
16.10.2003, 21:35
please mail me the tempory fix!

amirhadi@t-online.de

thanx!

CptMiller
18.10.2003, 10:34
Venom i didnt get any mail yet?

Development
18.10.2003, 15:06
Wasn't it you who mailed me it worked fine after i sent him fix?;-)
There were already bunch of guys....
Mail me and explicitly say who you are.

Malevolent
19.10.2003, 09:23
Operating System: Windows 2000 SP 4, recent security patches
Burning Software: Nero 5.5.9.13
Anti-virus Software: NAV 10.0
DAEMON Tools Version: 3.41

My Win2K machine will not fully boot up after installing DT 3.41. It hangs right after the keyboard flashes during the Win2k Splash screen. If I disable the ST3SHARK SCSI in safe mode, it will then boot up fine. It does keep trying to install a new controller while disabled although. I removed DT 3.41 and reinstalled 3.29, and that version still work fine without a problem. I rebooted several times to make sure it worked after reboots also.

Here are some system event errors when 3.41 was installed

Event Type: Error
Event Source: st3shark
Event Category: None
Event ID: 4
Date: 10/18/2003
Time: 11:59:33 PM
User: N/A
Computer:
Description:
The description for Event ID ( 4 ) in Source ( st3shark ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. The following information is part of the event: .
Data:
0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 08 00 00 00 c0 00 00 c0 ....А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........


Event Type: Error
Event Source: Service Control Manager
Event Category: None
Event ID: 7026
Date: 10/19/2003
Time: 12:01:32 AM
User: N/A
Computer:
Description:
The following boot-start or system-start driver(s) failed to load:
st3shark

Froggy31
20.10.2003, 01:35
Operating System: Win XP
Burning Software: nero
Anti-virus Software: norton 2003
DAEMON Tools Version: 3.41

Where do I need to put the temporary file ??

Thx

Phortje
27.10.2003, 20:17
Operating System: Windows XP Professional SP1
Burning Software: none
Anti-virus Software: Norton Antivirus 2004
DAEMON Tools Version: 3.41

Hey, i got exactly the same problem. This Windows XP install is 1 day old, so no mess.. On win2k DT ran perfectly... I'd be very glad if you could send me the workaround version.. Reinstalling DT after every reboot doesn't make me happy ;)
If you need any error dumps just ask me and tell me where to find them :)

Here's the byte-dump:
0000: 00 00 00 00 01 00 5a 00 ......Z.
0008: 00 00 00 00 04 00 04 c0 .......А
0010: 00 00 00 00 c0 00 00 c0 ....А..А
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........


Phortje

Vaktare
28.10.2003, 00:13
Operating System: XPSP1
Burning Software: Nero6
Anti-virus Software: Norton AntiVri. 2k4
DAEMON Tools Version: 3.41

Hey, Im working with DT for a long time and it always worked fine but since 3.41 this f*cking Error keeps trucking trought my head! :evil:

So is there a fix for that prob. or do you know what is this Error about?

BlueMeanie
28.10.2003, 21:49
Operating System: Win XP
Burning Software: Nero 6 latest version
Anti-virus Software: none
DAEMON Tools Version: 3.41

I am having this same problem. On reboot I get the error messages. What I have been doing is going to device manager and then disabling and enabling st3shark SCSI controller and it works fine. Its still pretty annoying but better than uninstalling and reinstalling daemon tools every restart.

Psxplayer
30.10.2003, 00:52
Operating System: Windows XP SP1 with all available Updates
Burning Software: Nero latest Version, CloneCD, CDMate, Alcohol 120%
Anti-virus Software: Norton Antivirus 2004
DAEMON Tools Version: 3.41

thanks to BlueMeanie, your solution works fine, is much better as the other Solutions.

Poulpos
03.11.2003, 05:18
Operating System: WinXP Pro SP1
Burning Software: CloneCD 4.0.1.3 - Nero 5.5.10.42
Anti-virus Software: Norton Antivirus 2003 v9.05.15
DAEMON Tools Version: 3.41

A little Feedback...

I had the same problems with Daemon Tools too (v3.41 and also with v3.33) :

- A daily-working software becomes suddently inneficient after a reboot :(
- The Invalid device two msg boxes popping up at LogOn
- The ST3SHARCK SCSI Controller (v3.41) that's not working and the exactly same bits of error (see Phrotje, Malevolant, etc)
- The same waste of time at unistalling - reinstalling DT 3.41 or 3.33 for a 1-boot use... :?
- AND I confirm that dactivating / Reactivating the ST3SHARCK SCI Controller from the device manager seems to be a reliable and not so tiring way of fixing the problem. :!:

But to improve definitely this great tool it woud be nice to resolve this bug in it's next version. :D

I precise that I previously had a comparative problem with the same softwares but running under Win2KPro SP4. DT 3.33 stopped working properly. It created an error that occurred during the loading of Win2K, and the only way to boot was in Safe Mode. but the bad surprise was that the MSI installer didn't seem to function in Safe Mode. :evil:
These situations can be obviously annoying. But I know you're working on it, so I can't wait for it... :wink:

Poulpos

kipusoep
05.11.2003, 00:52
Operating System: WinXP Sp1
Burning Software: Nero 6
Anti-virus Software: None
DAEMON Tools Version: 2.88

To all of you, use an older version! I'm using 2.88 now, working fine! 8)

rmcknight
06.11.2003, 06:38
Operating System: win xp
Burning Software: none
Anti-virus Software: none
DAEMON Tools Version: 3.41 & 3.33

i have had all these issues and currently have the double invalid device after boot. please email me the temp fix asap. i will also be happy to provide any debuging help if i can!

flashcup
06.11.2003, 23:52
Operating System: Windows Xp Pro SP
Burning Software: Nero 6, Alcohol 120% 1.47,CloneCD 4.3.16
Anti-virus Software: Norton 2004 10.0
DAEMON Tools Version: newest

I use "Alcohol 120%",then I update my windows updates,after that I got the same problem,so everytime I wanna use Virtual ROM, I should do below things first:Computer>Hardware>Device Manager>ScSI and RAID controllers.

If anyone got good idea to solve this problem, Please E-mail me:flashcup@hotmail.com

Thanks!

Prettyhaitian
10.11.2003, 20:54
Operating System: Windows Xp
Burning Software: none
Anti-virus Software: none
DAEMON Tools Version: 2.88


Operating System: WinXP Sp1
Burning Software: Nero 6
Anti-virus Software: None
DAEMON Tools Version: 2.88

To all of you, use an older version! I'm using 2.88 now, working fine! 8)



Thanks alot its working fine for me now

Jackal_TFL
19.11.2003, 08:04
Operating System: XP Pro sp1
Burning Software: Nero 5 and Alcohol 120%
Anti-virus Software: none
DAEMON Tools Version: nearly all

i get the same problem, but if install 3.14 it works fine anything newer and it no work :cry:

Jackal_TFL
21.11.2003, 01:03
ive noticed that its only the version of damon tools that uses the plug and play bios extension that has the problems, for me anyway. version 3.26 and above as far as i can tell. well anywayz in the meantime i just gonna go to device manager and update driver to reinstall the driver everytime i wanna use it.

i got a feeling its a windows problem, but then again you guys woul know more about that than me :P

Jackiegoal
21.11.2003, 16:58
Operating System: Win XP
Burning Software: Nero 5
Anti-virus Software: Norton 2003
DAEMON Tools Version: 3.41

I heard something about a patch, could someone post it here? It's quite annoying, because I can only get to the homeserver here through another PC and the homeserver has Daemon on it, for a couple of functions. After a restart I will need to reinstall that driver and it's really a pain in the ass to do that through a network connection.

dr.art
24.11.2003, 15:43
Operating System: Windows XP Home
Burning Software: /
Anti-virus Software: Panda ANti-Virus
DAEMON Tools Version: 3.41

i have the same problem,can someone send me the fix to : dr.art@web.de ??Please

Fiskemanden
25.11.2003, 10:23
This ain't the first timei write in this threat.

I have tryed with DM 3,41 and god the problem " Invalid device "
One off the maker behind DM, have mail me, a fix.
That didn't work.
I have tryed with a older version af DM, and that didn't work eiter.
Now i'm using DM 2,88 and Alcohol 120%, and both programs works.

Sort off...

I don't get any problems any more about a invalid device, but I can't install anything. Non off my images works any more, even after that I have selectet Emulation,.

Frist I thourgt that the problem was my images, but they all seens to work on my other computer.
So the problem must be with my computer, and daemon tools.
But what is the problem?
And how do I fix it?

I can still play my games, and all that, for I will just use my cd'es, but I would like to use my images again, so I din't destroy my cd'es.

Please help me out.

Sorry, for my bad english.

/Fiskemanden - Angry about that DM still dosn't work after a format

cagrihan
02.12.2003, 10:02
Operating System: windows xp
Burning Software: nero 5.5.10
Anti-virus Software: norton 2003
DAEMON Tools Version: daemon341.exe

I have the same problem ( invalid device ) after a reboot.
this also happens with alcohol 120%.
i have mailed you for the fix. thnx

Nodens
06.12.2003, 19:07
Operating System: Win XP Pro
Burning Software: A lot.I'm not bug reporting and I'm lazy to list for no reason:p
Anti-virus Software: NOD32
DAEMON Tools Version: 3.41

I do not have that bug occuring to me but I think I can help some.

Firstly the mentioned adildr.sys file is a USB driver that controls the mode of USB transfers (BULK or ISOCHRONOUS). It is outdated/absolete and it's specificaly made so it won't load by the packagers of certain ADSL modem drivers. Do not worry about it at all just ignore the message about it or if you are specificaly using the SAGEM 840 (the one I use that made me research the adildr.sys error :wink: ) you can download the latest drivers that are preconfigured for french networks (weird driver releasing policy there:P) that means you won't get to select vcmux or LLC and VPI/VCI values during instalation but you can always configure them later on. Otherwise just ignore the error until your modem manufacturer releases drivers with adildr.sys completely removed from the package.

Now regarding the bug. Checking at what you guys listed, it looks to me like st3shark is using the same PNP identifier as some other device on your system. Specificaly I think ACPI/ESCD at boot assigns a PNP identifier to a device that is already taken by st3shark. Try this: Uninstall daemon tools, disable acpi in bios, enable the "plug and play operating system installed" option in bios if it's not enabled already and install daemon tools again. I think that will solve your problem. Plus you are better off without acpi since most implementations are out of spec and IRQ sharing creates lots of problems (eg with sound cards, stuttering issues etc).

sjwoo
16.12.2003, 18:26
Operating System: WinXP SP1a
Burning Software: Nero
Anti-virus Software: McAfee
DAEMON Tools Version: 3.41

I have this problem on one machine but not the other. The machine where the problem is occuring is running AMD Athlon XP 1800+ on a SiS chipset. The other machine, my laptop, is an Intel 1.0GHz (Compaq Presario 1720US) with an Intel 8280 chipset. So I'm guessing it's either the CPU or the chipset that's causing the problem.

My money is on the chipset. Others having this issue -- are you by any chance running a non-Intel chipset (such as VIA or SiS)?

LocutusofBorg
16.12.2003, 23:35
We tested it on different chipsets (VIA, SIS, Nvidia, even AMD-Chipset).
This is not the problem. Beside this there's a new Version soon