DT 3.47 causes my system to run unstable.

[Kinmaul]

Operating System: Windows XP Pro sp2
Burning Software: None
Anti-virus Software: None
DAEMON Tools Version: 3.47

After installing DT 3.47 I am getting hardlocks and blue screens within a few minutes after boot up. However after uninstalling the problems go away. Here is the error message I get when I blue screen:

DRIVER_IRQL_NOT_LESS_OR_EQUAL

Technical information: *** STOP: 0x000000D1 (0xF7020DD2, 0x00000005, 0x00000008, 0xF7020DD2)

I also have the small memory dumps saved if you would like me to email them to you.

Any clue as to why I am having conflicts with DT and my computer?

P.S.
The reason I don't have any anti-virus or Burning software installed yet is because this is a fresh install of Windows and I haven't installed them yet.

[Copytrooper]

Please send the minidump to support@daemon-tools.cc for analysis (with reference to this thread).

[Kinmaul]

done

[Copytrooper]

Hm, didn't get anything yet - please resend unpacked or RAR-packed.

[Kinmaul]

Re-sent email

[Copytrooper]

Unfortunately the minidumps are damaged, so no information to get from them :|

[Kinmaul]

What would cause the minidumps to be damaged? Hmmm maybe I should just reformat.

[jon_saxon@yahoo.com]

Re: DT 3.47 causes my system to run unstable.

Operating System: XP HOME SP2
Burning Software: DAEMON TOOLS 3.47
Anti-virus Software: NAV CE 7.6
DAEMON Tools Version: DT 3.47

I started having trouble with DT 3.46 after I converted my drive from FAT32 to NTFS this morning.

I was trying to load an ISO image of SUSE Linux Personal 9.1 and the PC would reboot each time. I did download the ISO image so I didn't burn it myself.

I found and installed DT 3.47 and have the same problem. I also noticed that my PC will reboot when I mount Civ III on the virtual drive.

I have only one virtual drive configured on this PC. I have not had similar problems on my older Celeron 466 running Windows XP Pro SP2. I'll test again though because I haven't really used DT since I applied SP2 on that PC.

I am getting EVENT ID 1003 CATEGORY (102) IN MY SYSTEM EVENT LOG. These messages went away for a bit after I recreated my paging file on the C: drive but when I tried to use DT 3.47 I started to see these errors again.

Operating System: Windows XP Pro sp2
Burning Software: None
Anti-virus Software: None
DAEMON Tools Version: 3.47

After installing DT 3.47 I am getting hardlocks and blue screens within a few minutes after boot up. However after uninstalling the problems go away. Here is the error message I get when I blue screen:

DRIVER_IRQL_NOT_LESS_OR_EQUAL

Technical information: *** STOP: 0x000000D1 (0xF7020DD2, 0x00000005, 0x00000008, 0xF7020DD2)

I also have the small memory dumps saved if you would like me to email them to you.

Any clue as to why I am having conflicts with DT and my computer?

P.S.
The reason I don't have any anti-virus or Burning software installed yet is because this is a fresh install of Windows and I haven't installed them yet.

[Copytrooper]

Did you update to SP2 with v3.46 installed? Did you get an error message (regarding atapi.sys) while installing SP2? Please check atapi.sys version installed (SP2 = 5.1.2600.2180).
Do you have minidump related to the crash? If so send newest file to support@daemon-tools.cc with reference to this thread.

[jon_saxon@yahoo.com]

I did update to SP2 with DT 3.46 installed.

I did not receive any error messages on this PC during the application of SP2. I did not receive any error messages on another PC with XP Pro and DT 3.46 during the application of SP2.

I do have several minidumps from today and will foward them.

My version of atapi.sys is 5.1.2600.2180 (xpsp_sp2_rtm.040803-2158)

The problems started just after I ran several defrags and converted my disk from FAT32 to NTFS. Before that with SP2 I was having no problems. Since then using either version of DT cause a reboot or lockup.

[DevX]

You seem to use XIMETA drive. It cannot operate with current Daemon Tools release. Mail me please to venom386@daemon-tools.cc

[jon_saxon@yahoo.com]

DT incompatible with Ximeta

That is really odd because I have been using DT 3.46 with Windows XP Pro SP1 and SP2 and Ximeta on another Celeron PC for several months and have never had a problem with it.

Is there a planned release to correct this from either DT or Ximeta?

[Copytrooper]

Please use contact address mentioned above for further information.