Conflict with DT and O&O Defrag

[CrendKing]

I installed DAEMON Tools 4.03 (with SPTD 1.24), and found there is an error message about SPTD in Event Viewer -> System, said "Driver detected an internal error in its data structures for ." Although I can use DAEMON Tools normally, sometimes there will be a BSOD with message IRQL_NOT_LESS_OR_EQUAL (which may describing some driver fault) when I exit Windows.

And after installing DT4.03, I cannot use O&O Defrag (I tried almost every version, even the unpublished versions I get from O&O Support). For example, I open O&O, analyze one volume. After the analysis completes, I begin to analyze some volume (same volume or some other volume) again, the progress would stop at 0% forever, and the agent service cannot be stopped. And as for defragmentation requires analysis first, I can use O&O only ONCE every time I boot Windows.

I can assure it's a conflict with DAEMON Tools and O&O Defrag (manually delete SPTD, no problem), and SPTD is the most suspected component I think. Is there anyway to install DT4 without installing SPTD, and DT4 will work without installing SPTD? Thanks!

[Andareed]

I haven't tested O&O but I know dtools works fine with Perfect Disk and Diskeeper. I'll take a look at O&O defrag later today.

[CrendKing]

Yes, PD and Diskeeper works well, only O&O has the problem. Maybe there is some low-level difference in those core engines.

[LooDos]

i had this problem too a long time ago. i think with DT v3.47 and O&O defrag. could be quite interesting to solve this problem...

[CrendKing]

But DT 3.47 and StarForce... You know...

[AnalCobra]

I use DT 4.03 and O&O Defrag 8 and it works perfectly.

[DomiOh]

I used O&O Defrag 8 without problems with DT 3.47
Not tested with 4.03 yet.

[LooDos]

i had problems using DT 3.47 and O&O Defrag 8.
it simply didnt defrag automatically anything...

[CrendKing]

Yes, I do think that this is a system-related problem, and maybe SPTD first conflicts some other driver in my system, and becomes malfunction, then O&O would invoke some low-level disk driver, such as SPTD, and finally, this problem occurs.

I think the most important thing is to solve "Driver detected an internal error in its data structures for .", as this does NOT ONLY OCCUR in my computer.

[DevX]

What are binary bytes in SPTD error message in system event log?

[CrendKing]

0000: 00 00 00 00 01 00 52 00 ......R.
0008: 00 00 00 00 04 00 04 c0 .......À
0010: 86 00 00 00 01 00 01 00 .......
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........

This error raises each time when I boot Windows.

[DevX]

There is somethng wrong with your storage controllers or some
"unusual" drivers used. Please report your configuration.

[CrendKing]

My Motherboard is Soltek SL-KT600-R, southbridge is VT8237. I have a SATA harddisk and an PATA harddisk. SATA driver is the "VT8237 Integrated Serial ATA RAID controller 5.20A" (http://www.viaarena.com/default.aspx...&SubCatID=143), and IDE driver is the "VIA IDE Accelerator Driver 1.21 BETA" (http://www.viaarena.com/default.aspx...&SubCatID=148).

In Computer Management, IDE controller is "VIA Bus Master Ultra ATA Controller", SCSI and RAID controller is "VIA SATA RAID Controller".

Anything else should I report?

[DevX]

Please report your registry settings under HKLM\HARDWARE\DeviceMap\Scsi - which driver is shown
for every "ScsiPort X"subkey?

What is your OS version?

[CrendKing]

OS is Windows XP Pro with SP1

Registry:

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 0]
"Interrupt"=dword:00000014
"IOAddress"=dword:0000e800
"Driver"="viamraid"

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 0\Scsi Bus 0]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 0\Scsi Bus 0\Initiator Id 255]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 0\Scsi Bus 0\Target Id 0]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 0\Scsi Bus 0\Target Id 0\Logical Unit Id 0]
"Identifier"="ST3120026AS 3.18"
"Type"="DiskPeripheral"
"InquiryData"=hex:00,00,00,00,1f,00,00,00,53,54,33 ,31,32,30,30,32,36,41,53,20,\
20,20,20,20,20,20,20,20,20,20,20,20,33,2e,31,38

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 1]
"Interrupt"=dword:00000009
"IOAddress"=dword:0000ffe0
"Driver"="dtscsi"

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 1\Scsi Bus 0]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 1\Scsi Bus 0\Initiator Id 15]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 1\Scsi Bus 0\Target Id 0]

[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\Scsi\Scsi Port 1\Scsi Bus 0\Target Id 0\Logical Unit Id 0]
"Identifier"="JD1793W LBJ049G 1.0 "
"Type"="CdRomPeripheral"
"InquiryData"=hex:05,80,02,02,20,00,00,10,4a,44,31 ,37,39,33,57,20,4c,42,4a,30,\
34,39,47,20,20,20,20,20,20,20,20,20,31,2e,30,20

Seems one is my harddisk, one is DT.